Hand knitters often struggle with this method for binding off because they usually work it directly off their hand knitting needles. When worked off properly knitted scrap knitting, it couldn’t be easier to do. In fact, even when I hand knit a ribbed neckband, I transfer the stitches from the hand needles to the machine and scrap off as I will describe below. It makes all the difference.
First of all, the stitches need to present as two separate rows of stitches that you can think of as upper and lower rows. This is the factor that makes it easier to see what you are doing and enables you to distinguish which stitch to work and how. The work is scrapped off in a way that creates those two visual rows for you.
This bind off is worked the same for latched up ribbing as it is for double bed ribs. Let’s assume you have worked your ribbing on a double bed machine. End with the carriage on the right. Transfer all the ribber stitches to the main bed, pulling each needle out to Holding Position (HP) as you deposit the stitches. Cut the yarn, leaving a tail about 3 times the width of the knitting. Drop the ribber bed out of the way and, if necessary, switch to the single bed arm/sinker plate.
Set the carriage to Slip all needles in Working Position (WP) and to knit needles back from HP. The stitch size should be set for stockinette. You can use ravel cord for the first two rows or, for practice, just knit with waste yarn that contrasts well with the rib. Knit 1 row. The needles in WP should have slipped; the needles in HP should have knitted. For the example in the video, I knitted a second row with ravel cord and then switched to waste yarn.
Set the carriage to knit in both directions. Knit 8-10 rows of waste, cut the yarn and then drop the work from the machine. I usually press the waste yarn (not the rib) to assure that it lies flat and is less likely to ravel.
Please refer to the video included in this post for the visuals to accompany these directions. The numbers below also appear in the video as I work each step. Thread the main yarn tail through a blunt yarn needle and hold the work as shown in the video, beginning on the right edge. You should be able to clearly distinguish between an upper and a lower row of stitches held by the pink ravel cord. For most of the video, I held the fabric flat to avoid confusion, but it is actually easier to work the stitches with the waste knitting folded back – the two rows of stitches pop right up. Make sure you stitch through the actual stitches – not the ravel cord stitches.
1. Insert the needle down through the first stitch in the top row and then down through the first stitch in the bottom row. Pull the yarn through the stitches, pulling just snuggly enough to eliminate any excess length, but do not tighten the stitches.
2. Insert the needle back down through the first (upper) stitch and then up through the next upper stitch (down and up). Pull the yarn through the stitches just enough to eliminate excess length – not too snuggly. [The same goes for all following stitching whether or not I keep saying it].
3. Now, insert the needle up through the bottom row stitch you worked before and down through the next bottom row stitch (up and then down). It is important to notice how the yarn passed over the work when I switched from working the upper row to the lower row. That is actually what forms the edge itself.
4. Pass the yarn over the work and insert the needle down through the last stitch you worked on the upper row and then up through a new stitch (down and then up).
Each stitch is worked – twice – first as the second (new) stitch in each sequence and then as the “old stitch” in the next sequence. This is essential. Also, notice that whenever you work the upper row of stitches, the needle always enters down the old stitch and up through the new stitch. When working the lower row of stitches, the needle passes up through the old stitch and down through the new one. So, the upper row of stitches end with an “up” stitches and the lower row ends with a “down” stitch. This alternation, to, is essential.
5. This is the next bottom row sequence so the needle works up and then down. Continue to alternately work a pair (1 old and 1 new) of upper row stitches with a pair of lower row stitches until you reach the left edge of the fabric. You might be able to work both stitches with a single needle motion or it might be necessary to fully insert the needle through the first stitch and then through the second. It usually depends on the size of the stitches.
6. When you reach the left edge, work the last upper row stitch and then insert the needle up through the last lower row stitch and down through the last upper row stitch to end.
Pull out the ravel cord – or ravel the rows of waste knitting and behold your perfect edge! I usually run a thin knitting needle or blocking wire through the edge and give a strong tug to help set the stitches. You could also thread a yarn needle with some ravel cord, thread it through then pull against it to set the stitches. You will notice that the bind off tends to roll to one side, the side that faced you as you worked. Therefore, it is a good idea to always work with the wrong side of the sweater facing you.
This bind off can be worked from left to right just as easily if you are left handed or your yarn ended on the left side to begin with. For neckbands, I usually join one shoulder seam, work the entire neckband, scrapping it off as I described above and then I join the second shoulder seam. When I work the bind off, I try to make the ending stitches as blend as smoothly as possible with the beginning stitches so the edge is continuous and smooth.
This method – and lots of other great techniques are shown with excellent illustrations in The Guide to Knitting Techniques, a paperback book from Silver Reed that is still available. The book sells for $36 and you can purchase it from The Knit Knack Shop.
This book was originally one of a hard-bound set. The other book deals with specific knitting directions for the garment patterns that came with the charting attachment that used to be built into the machines (or available as an accessory). I don’t think the garment book has been available for a very long time and, although the knitting directions might be helpful for a novice, they are very specific to the old patterns – which have very little ease and even less style. If you happen upon an inexpensive copy, don’t pass it up, but don’t pay a lot of money for it either!
Remember – only a couple more weeks till the new Craftsy class launches and I am giving away FIVE FREE CLASSES to blog subscribers! Sign up so you have a chance to win!