Talk about something I wish I had invented, but didn’t! I LOVE this edging/Bind Off/trim and have used it for all kinds of things over the years. With Judith Duffy’s kind permission, it appeared in Hand-Manipulated Stitches for Machine Knitters (page 183) and there was even a hand-knit version of it in Knitters’ Magazine to accompany the machine knit pattern I did for the gold sweater that appeared in the blog post of March 7, 2016 – and again here (below).
I first saw this edging when I was a contributing editor for Threads Magazine (in the earliest years of the magazine) and they were doing a feature article on fiber artist Judith Duffy’s work. They asked me to choose one of her textures to reproduce for the article and I spent some time figuring out machine knit directions for the cabled edging. Do you remember the wolf-in-sheep’s-clothing garment that graced a back cover in those early years? It was a stunning piece by Duffy and unlike anything I have seen before or since, hand or machine knitted.
The gold sweater at left is a twisted stitch and latched up tuck stitch pattern (see previous blog 3/7/16), but take a close look at the edge of the ribbing. I started all the garment pieces on waste yarn and went back later to work the ribs. Instead of a conventional rib bind off, I worked the Duffy Cabled Edging to trim and bind off the ribs all at once.
Most of all, I think I have used it to bind off neckline stitches when shaping a neckline with short rows, preserving live stitches. On a standard gauge machine it produces a lovely, delicate neckline finish.
You can also use this edging to join two garment or afghan sections together by rehanging them on the machine with the wrong sides facing each other and then working the edging. As with the I-cord join (blog 4/8/16), make sure you always hang the pieces the same way as there is a right and wrong side to the way the edging joins the base fabric.
The method is quite simple. Hang the work on the machine with the right side (whatever that is) facing you – live stitches or selvage edges (whole stitches are best). All of the needles except the first 3 on the carriage side are in holding position and the carriage must be set to hold needles in HP. Knit 12 rows over the 3 working needles and then remove those stitches on a 3-prong tool and pass the tool under the adjacent 3 needles and re-hang the stitches on the 4th, 5th and 6th needles from the edge.Place the empty needles in NWP. Repeat till you either reach a corner or the end. If you want to turn a corner, add two more rows to the last two groups on each side to help make the corner so that it doesn’t flatten out. You’ll also find that you can’t easily hang the next side of an afghan until you get right to the corner. At that point, you might want to remove those last few stitches and re-hang them on the far right end of the bed to give you lots of needles to re-hang the next side.
I almost always work with 3 stitches and knit 12 rows for each spiral, but you can certainly work with more stitches if you have a tool to handle them. Twelve rows almost always works out right, but you might find that 10 or 14 are better so work the edging on your gauge swatch to find out before you begin. You might also find that you want to adjust your stitch size a bit smaller or larger – sampling always pays off.
As I said in the tutorial, the float that passes underneath the first 3 needles always gets hidden inside the spiral, but you can certainly opt to knit those needles back and eliminate the float if – for some unforeseen reason – it shows. Also, by way of variation, I have seen students work this trim in two colors, which is very cool. In that case, it might be best to knit back the float of at least one of the colors.
When you reach the end, you want the trim to end quickly and neatly. What I have always done is to knit half as many rows on the second to last group and then immediately reduce those 3 stitches to a single stitch. Move that single stitch to the last needle at left, knit 1 row over the last 3 needles and then reduce those stitches to a single stitch and pull the yarn tail through to secure.
I think there are all kinds of creative possibilities for this edging – I love the cabled effect and the fact that it also binds off stitches. Lately I have been playing with a cabled cord effect by e-wrapping, knitting 1 row over all needles and then working the JDCE. I think it still needs a little work and then I will share it with you! What other ways can you think to use this trim?