Doing it Double!

If your machine has a ribber, you probably don’t have a lot of use for a double latch tool. However, if you use a single bed machine, you’ll find a double latch tool can save you lots of time. Initially, it might feel a little clumsy to use, but, like anything else, once you get going a double latch tool is a wonderful thing to have!

Double latch tools make it much faster to re-form stitches for 1×1 or 2×2 rib, whether you want a ribbed band or just some columns or blocks of rib stitches in the body of a garment. The latch hooks need to be spaced for the gauge of your machine and they all work pretty much the same way.  Here are some tips for success:

First of all, Insert the tool at the bottom of the columns of stitches you plan to drop and then drop the stitches from the needles above, rather than dropping the stitches and then fishing around for the stitches. It is much safer and a lot less frustrating, but you also have greater control over how far down the stitches drop.

Keep plenty of downward tension on the ladder of stitches you are reforming so that the individual bars do not split as you work them.

Push the tool just far enough away from you to make sure the “old” stitches open the latches and slide back over them. Catch the next bars of the ladder in the hooks of the tool and pull just hard enough to make sure the old stitches are pulled over the latches to form the new stitches. If you look at the video carefully, you will see that the surrounding stitches move very little, which is how it should be. You don’t want to start distorting adjacent stitches.

When you work with a single latch tool, the last stitch is transferred from the tool to a needle on the bed by hooking the tool onto the needle. This isn’t possible (at least not easily!) when using a double latch tool. Instead, when you reach the top of the column, hold the tool above the edge of the bed and just poke the needles through the back of each stitch. Make sure you keep some tension on the tool so that the stitches are easier to see and easier for the needles to enter. Once you poke the needles through the back of the stitches, you can just remove the tool.

Back in the day (as they say), many knitting machines came with double latch tools, although they were usually standard gauge machines – both European and Japanese. The hooks projected straight out from the end of the handle. At www.guagliumi.com I have double latch tools for 2×2 rib for 4.5, 6.5 and 9 mm machines, tools for 1×1 rib for 6.5 and 9mm machines.  I designed these tools with the metal perpendicular to the wooden handle because I find the much easier to work with – I hope you do too!

 

 

Latching Up Stitches

This is the first of a series of short “How-To” lessons I plan to post here on the blog. While the information is old hat to a lot of you, there are so many new knitters out there (working on used machines all by themselves) that I figured I would start with some basics and then get progressively more involved and creative as time rolls on.

I think the important thing for new knitters to know about handling the latch tool is that slower, smoother motions ultimately end up being a lot faster than having to re-do the same thing over and over. Speed comes with experience so don’t rush it!

When I latch up a stitch, I concentrate on making sure that the old stitch slides smoothly over the latch to open it before I catch the next ladder bar in the open hook. Then just pull back enough for the old stitch to close the latch and slide over it. The fabric itself should hardly move – let the tool do the work.

When reforming stitches from the purl side, I always insert my tool into the bottom stitch in the column then release the stitch from its needle and let the stitch drop back to the tool. Dropping first means you would have to poke around to insert the tool through the stitch and sometimes that isn’t as easy as it looks. Doing it first is much safer and a whole lot easier.

I really love the way a tuck stitch looks along side cables and in addition to looking a bit more open than a reformed knit stitch (purl on the other side), tuck has the added advantage of returning a little width to the fabric. Lots of cables can cause a fabric to become narrower so using a tuck at each side of a cable actually returns that width to the fabric. With very large sizes, it could mean the difference between having enough needles – or not – to knit your garment!